S & W Wilson Ent., Inc.

1) Installation of filter:

• Put white coral and black carbon with the bag into the filter (don't open the bag);
• Take the poly-fill, polyester fiberfill out of the bag and place it on top of the coral and carbon;
• Place the filter pad on top of the polyester fiberfill.

2) Installation of fish tank:

• Put the fish tank on top of the stainless steel stand, connect the 1"&1-1/2" union of the pipe which are located under the fish tank.
• When the fish tank is running, the water valve under the fish tank and the grey water valve of the water pump are always closed.
• The valve in the front side and back side of the water pump is always open.

3) Making the sea salt water:

• Fill in water to the tank directly, the water will go to the filter after it fills up.
• Plug in the power when the water fills over half of the filter, then start the water pump and condensing unit. (ALWAYS keep the water over half of the filter.)
• Add sea salt into water: 100lbs salt can conduct 330-gallon sea salt water. It's good to have the concentration between 1.020 and 1.022. Please use the hydrometer that comes along with other materials to test the concentration of the water.
• To use a hydrometer, fill up the test jar with the water to be measured; place the hydrometer in the jar:

1. If the green line is far away and below the horizontal line, the concentration of the water is too low and should add more sea salt;
2. If the green line is far away and above the horizontal line, the concentration of the water is too high and should add more water;
3. If the green line touches the horizontal line, the concentration of the water is good.

4) Adjustment of the temperature control:

• Please go toProgram the Thermostate for detail.

     (Different tempature for different seafood, if you don't know the temperature

      for your seafood, please call us. 718-965-2227)

* Caution:

    a) The water in the fish tank will reach the set temperature and complete the

         filter process after the water pump and condensing units run for ten hours.

     b) if in seven days:

                       Survival of lobsters, crab less than ----- 90%

                       Survival of fishes less than --------------- 80%

      Please check the following and make correction:

                  1) If the temperature is correct.

                  2) If the concentration of the water is correct. (1.022).

                  3) The filter system and transparency of the water

      If all of above are correct, please call us. (718-965-2227)

      c) To avoid breaking the seal, NEVER turn on the water pump without filling in

           water to the tank. 

安装及使用说明 

1）过滤器的安装:

• 把白色的珊瑚和黑色的活性碳连网袋一起放入过滤缸内 (千万不要打开网袋).
• 取出胶袋内的碎棉花(Poly-fil, polyester fiberfill)放在珊瑚与活性炭的上面.
• 把可清洗的整块粗过滤棉放在最上面加上两条压条.

2) 鱼缸的安装:

• 将透明的鱼缸放在不锈钢座上,连接缸底的1"和1-1/2"上,落水塑料管的活接口(UNION).
• 缸底的放水制和水泵出水管后的灰色放水制,使用时是关闭的.
• 水泵前后的水制(VALVE)是常开的.

3) 鱼缸加水和海水的调制:

• 直接加水j进鱼缸内,水满后会自动流到过滤器内,过滤器内的水位超过碎棉(在视镜内可以看到)即可.
• 过滤器内的水位达到要求后,即可接通电源,开动水泵和制冷压缩机.
• 如果鱼缸准备养海水的龙虾,大蟹,海鱼等,可以用海盐调配人工海水.海水的浓度为1.022.
• 100磅盐可调约330加仑海水,用附送的比重计(HYDROMETER)测量,

         A)如果绿色在水平线的下面,太淡,加盐.

         B)如果绿色在水平线的上面,太咸,加水.

         C)如果水平线在绿色中间,盐度正确.

4) 温度控制器的调整:

• 请参考 Program the Thermostate

     (不同的海鲜,不同的温度,如果不知道请来电询问 718-965-2227)

* 注意事项:

   a)在水泵和冷冻机运行十小时后,鱼缸内的水才能达到设定的温度和过滤完毕.

   b)如果七天内:

                       龙虾,大蟹存活率小于 ------ 90%

                       鱼类存活率小于 ------------- 80%

      请检查以下3点并且更正:

                 1) 温度是否准确.

                 2) 水的盐分是否准确(1.022).

                 3) 水的过滤系统和透明度.

       如果以上三点都正常,请来电询问解决方法 (718-965-2227)

   c) 请勿在加水进鱼缸之前开动水泵。